Concrete cutting in Dixon CA - clean, straight cuts right where you need them
Need a cracked panel cut out, a trench opened or a doorway cut in a wall? We cut it clean and keep the mess contained.
- Licensed and insured.
- Free in-person estimates.
- Replies within 1 business day.
When do you need concrete cutting to trim a slab, open a trench or cut into a wall?
Concrete cutting in Dixon opens or trims concrete that's already in place, so you can change a driveway, patio, floor or sidewalk, or cut a door or window opening into a concrete or block wall, without tearing the whole thing out. It's often the first step before a new pour, a pipe repair or a remodel.
Most people call us when something already in place is in the way: a driveway that needs to be wider, one cracked panel, a pipe under the garage floor, or a wall that needs a door. The price mostly turns on how long and how deep the cut is, whether it's a floor or a wall, how easy the spot is to reach and how much dust control the room needs. The schedule turns on what's inside or under the concrete and whether the cut touches a city street, so I'd rather see the spot than guess, and the estimate at your site gives you the figure for your own cut.
How do you know a slab or wall needs cutting?
One cracked or sunken panel
One section of the driveway or walk has cracked through or dropped below the rest while the others still sit fine. That usually means the ground gave way under that piece, and cutting it out on clean lines lets us replace just that part instead of the whole slab. Left alone, a dropped edge catches toes and lets water run under the panels next to it.
A line runs under the slab
You need a new drain, a water line or a repair to a pipe that runs under the concrete. A narrow cut and trench gets to it without breaking up the whole floor. A leak under concrete keeps soaking the ground the slab sits on, so it's worth getting to soon.
A wall where you want a door
You want a door into the garage, a bigger window in a block wall or a wider opening between spaces. Breaking through with a hammer and chisel leaves ragged edges and can crack more of the wall than you meant to, so this is a job for a saw set up for walls.
Work that often follows a cut
Concrete driveway building
Widening a driveway or replacing a sunken section starts with a clean cut, then a new pour on a base that's dug out and packed.
Concrete patio construction
When you're reshaping a patio or adding onto one, the cut sets the edge the new slab meets, so the joint lands where you want it.
Concrete cutting, the way we do it
You tell us where the cut goes, and we match the method to it, because a driveway edge, a trench through a garage floor and a doorway in a block wall each need a different saw. When the slab could have cables in it, we check before the blade goes in. We pick wet or dry cutting based on what's next to the cut, mark the lines, make the cut, break out and haul away the pieces, and leave the edges ready for whatever comes next.
Cutting is usually the start of a bigger job. When you're widening a driveway or swapping out a broken panel, we cut the old edge straight and go right into concrete driveway building, and the same goes for trimming or opening up a patio ahead of concrete patio construction, so the new slab meets the old one along a clean line.
Flat cuts in slabs
For driveways, patios, sidewalks and garage floors, when you're widening, removing a damaged section or opening a trench for a line. It covers most homeowner jobs, since the cut runs straight and the slab around it stays put.
Openings in walls
For a new door or window in a concrete or block wall, cut with its own setup rather than the floor saw. We go over what the wall carries at the estimate visit, before anything gets marked.
Get a price for cutting your slab or wall
Send the form and we'll get back to you within one business day to set up a visit. The estimate is free with no obligation, and you can call (707) 640-8084 instead.
Call (707) 640-8084Why Dixon homeowners call Premier Dixon Concrete to cut concrete
I see every job myself
I come out to look at every job myself, and I'm on site running our crew when the cutting gets done. The person who marked the cut is standing next to it when the blade goes in, so nothing gets lost between the estimate and the work.
Two licenses worth asking about
We're licensed and insured. Dixon asks contractors to hold a city business license as well as a California contractor's license, and the state license board lists concrete sawing and coring under its concrete related services class, so ask anyone you're thinking of hiring about both licenses.
Slurry kept out of drains
Dixon's storm drains are separate from the sewer and carry rainwater out through ditches to Hass Slough, and the city makes it unlawful to put anything else in them. We collect the slurry, the gray mix of water and grit the saw throws off, so it stays out of the gutter and the inlet.
Running this business since 2023
I poured flatwork when I was young, did other work for years and started this business in Dixon in 2023 because concrete is what I'm good at. You get a straight answer on what a cut will and won't do before you spend anything.
A good cut is mostly planning, so tell us about your job and I'll come take a look, here in Dixon or in the cities around it like Vacaville, Davis and Fairfield.
What happens after you call about a concrete cut in Dixon?
Call or send a message
Call (707) 640-8084 or send the form, and we get back to you to set a time for me to come out. A photo of the spot helps me show up with the right questions.
I come out and look
I look at the slab or wall, what's around it and what the opening is for. You get an estimate with the method I'd use, how we'll handle the dust and water, and the price for your cut.
We handle permits and cut
Once you say go, we take care of any permit steps and make the cut. If the job includes digging afterward, USA North 811 has to be called at least two working days before, not counting the day of the call, so that wait goes on the schedule.
Cleanup and a walkthrough
We haul off the broken pieces and clean up the work area. If a patch or new pour follows, I walk you through curing, the wait before the new concrete is ready to use, before we leave.
Common questions
Which concrete cutting method fits my job?
For floors, driveways and sidewalks, the usual tool is a walk-behind saw with a large diamond blade, which is the most common way to cut flat concrete. Door and window openings in a wall use their own standard setup, so the first thing we'll ask is where the cut goes and what it's for.
Can cutting into a concrete slab damage it?
It can if the blade hits a post-tension cable, a steel cable pulled tight inside some slabs. One scanning company warns that cutting one can damage the structure and advises a professional scan of the exact work area first, which is why we check when your slab could have them. If you have structural records for the building, pass them along, since that company pairs its scans with those records.
How much does concrete cutting cost per foot?
Professional concrete cutting across the US usually costs about $3 to $10 per linear foot. That's the going range for the work, not our price, and the estimate at your site gives you the figure for your own cut.
Do I need a permit to cut into a street in Dixon, CA?
Cutting into a newly paved or resurfaced street in Dixon needs an approved street-cut moratorium waiver, the city's sign-off to dig into fresh pavement, before an encroachment permit, and the City Engineer decides on it. For other street work, the City of Dixon permits office is where to ask. If your job needs a permit, we pull it and set up the inspections, and when we're not sure, we ask the city before we start.
What is the best way to cut concrete inside a finished room?
One diamond tool company's guide advises pulling the dust off at the tool instead of using water, with a shroud over the blade, a dust collector and a HEPA vacuum. It says that cuts slower than wet cutting but can't damage your finishes, so you trade some time for floors and walls left unharmed. Crews in California also work under Cal/OSHA's construction standard on silica dust when cutting in an existing building, so ask us at the estimate how we'll handle it.
How do I replace just the cracked part of my driveway?
Have the damaged panel cut out along straight lines, dig out and pack the ground under it, and pour a new section to meet the old edges. The new piece usually won't match the old color right away, and if the ground under the rest is failing too, a full replacement can make more sense, which I'll tell you straight at the visit.
Tell us where your cut goes
Call (707) 640-8084 or email info@concretedixon.com with where the cut goes, its rough length in feet, whether it's a floor or a wall, and any structural records for the building, so I show up with a plan instead of guesses.